Der erste Reboot nach den vorherigen Anpassungen ist im folgenden dargestellt:

LILO 22.3.4 boot: 
boot: lxser
Loading lxser......................................................................
BIOS data check successful
Bootdata ok (command line is BOOT_IMAGE=lxser ro root=fd00 console=tty0 console=ttyS0,57600 panic=30)
Linux version 2.6.5-7.244-smp (geeko@buildhost) (gcc version 3.3.3 (SuSE Linux)) #1 SMP Mon Dec 12 18:32:25 UTC 2005
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009e000 (usable)
 BIOS-e820: 000000000009e000 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 00000000dfee0000 (usable)
 BIOS-e820: 00000000dfee0000 - 00000000dfee3000 (ACPI NVS)
 BIOS-e820: 00000000dfee3000 - 00000000dfef0000 (ACPI data)
 BIOS-e820: 00000000dfef0000 - 00000000dff00000 (reserved)
 BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
 BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
 BIOS-e820: 0000000100000000 - 0000000120000000 (usable)
Scanning NUMA topology in Northbridge 24
Number of nodes 1 (10000)
Node 0 MemBase 0000000000000000 Limit 000000011fffffff
Using node hash shift of 21
Bootmem setup node 0 0000000000000000-000000011fffffff
No mptable found.
On node 0 totalpages: 1179647
  DMA zone: 4096 pages, LIFO batch:1
  Normal zone: 1175551 pages, LIFO batch:31
  HighMem zone: 0 pages, LIFO batch:1
Nvidia board detected. Ignoring ACPI timer override.
ACPI: RSDP (v000 Nvidia                                    ) @ 0x00000000000f7a60
ACPI: RSDT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x00000000dfee3040
ACPI: FADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x00000000dfee30c0
ACPI: SRAT (v001 AMD    HAMMER   0x00000001 AMD  0x00000001) @ 0x00000000dfee9780
ACPI: MCFG (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x00000000dfee98c0
ACPI: MADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x00000000dfee9480
ACPI: DSDT (v001 NVIDIA AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x0000000000000000
ACPI: PM-Timer IO Port: 0x1008
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:3 APIC version 16
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1 15:3 APIC version 16
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
Checking aperture...
CPU 0: aperture @ 8000000 size 32 MB
Aperture from northbridge cpu 0 too small (32 MB)
No AGP bridge found
Your BIOS doesn't leave a aperture memory hole
Please enable the IOMMU option in the BIOS setup
This costs you 64 MB of RAM
Mapping aperture over 65536 KB of RAM @ 8000000
Built 1 zonelists
Kernel command line: BOOT_IMAGE=lxser ro root=fd00 console=tty0 console=ttyS0,57600 panic=30
Initializing CPU#0
PID hash table entries: 16 (order 4: 256 bytes)
CKRM Initialization
...... Initializing ClassType<taskclass> ........
...... Initializing ClassType<socketclass> ........
CKRM Initialization done
time.c: Using 3.579545 MHz PM timer.
time.c: Detected 2210.221 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
Memory: 4038508k/4718592k available (2458k kernel code, 0k reserved, 1225k data, 204k init)
Security Scaffold v1.0.0 initialized
SELinux:  Disabled at boot.
Mount-cache hash table entries: 256 (order: 0, 4096 bytes)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 0(2) -> Node 0
Using local APIC NMI watchdog using perfctr0
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 0(2) -> Node 0
CPU0: Dual Core AMD Opteron(tm) Processor 175 stepping 02
per-CPU timeslice cutoff: 1023.90 usecs.
task migration cache decay timeout: 2 msecs.
Booting processor 1/1 rip 6000 rsp 1011ffa5f58
Initializing CPU#1
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 1(2) -> Node 0
Dual Core AMD Opteron(tm) Processor 175 stepping 02
Total of 2 processors activated (8765.44 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x21 pin1=0 pin2=-1
Using local APIC timer interrupts.
Detected 12.558 MHz APIC timer.
checking TSC synchronization across 2 CPUs: passed.
Disabling vsyscall due to use of PM timer
time.c: Using PM based timekeeping.
Brought up 2 CPUs
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Looking for DSDT in initrd ...No customized DSDT found in initrd!
khelper: max 64 concurrent processes
resid is -1 name is io <NULL>
CKRM .. create res clsobj for resouce <io>class <taskclass> par=0000000000000000
NET: Registered protocol family 16
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040326
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
Transparent bridge - 0000:00:09.0
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK2] (IRQs 3 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK3] (IRQs 3 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNK4] (IRQs 3 5 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK5] (IRQs 3 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LUBA] (IRQs 3 5 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LUBB] (IRQs 3 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LMAC] (IRQs 3 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LACI] (IRQs 3 *5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LMCI] (IRQs 3 5 *7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LSMB] (IRQs 3 *5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUB2] (IRQs 3 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LIDE] (IRQs 3 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSID] (IRQs 3 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LFID] (IRQs 3 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LPCA] (IRQs 3 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled.
ACPI: PCI Interrupt Link [APC3] (IRQs 18) *11
ACPI: PCI Interrupt Link [APC4] (IRQs 19) *10
ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCP] (IRQs 20 21 22 23) *0, disabled.
PCI: Using ACPI for IRQ routing
PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off'
ACPI: PCI Interrupt Link [APCS] enabled at IRQ 23
GSI 23 assigned vector 0xA1 and IRQ 16
ACPI: PCI interrupt 0000:00:01.1[A] -> GSI 23 (level, low) -> IRQ 16
ACPI: PCI Interrupt Link [APCF] enabled at IRQ 22
GSI 22 assigned vector 0xA9 and IRQ 17
ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 22 (level, low) -> IRQ 17
ACPI: PCI Interrupt Link [APCL] enabled at IRQ 21
GSI 21 assigned vector 0xB1 and IRQ 18
ACPI: PCI interrupt 0000:00:02.1[B] -> GSI 21 (level, low) -> IRQ 18
ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
GSI 19 assigned vector 0xB9 and IRQ 19
ACPI: PCI interrupt 0000:01:05.0[A] -> GSI 19 (level, low) -> IRQ 19
ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
GSI 18 sharing vector 0xB1 and IRQ 18
ACPI: PCI interrupt 0000:01:09.0[A] -> GSI 18 (level, low) -> IRQ 18
ACPI: PCI interrupt 0000:04:00.0[A] -> GSI 19 (level, low) -> IRQ 19
testing the IO APIC.......................

.................................... done.
PCI-DMA: Disabling AGP.
PCI-DMA: aperture base @ 8000000 size 65536 KB
PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture
Initial HugeTLB pages allocated: 0
IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
VFS: Disk quotas dquot_6.5.1
Initializing Cryptographic API
Real Time Clock Driver v1.12
Non-volatile memory driver v1.2
Linux agpgart interface v0.100 (c) Dave Jones
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 128000K size 1024 blocksize
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE-CK804: IDE controller at PCI slot 0000:00:06.0
NFORCE-CK804: chipset revision 242
NFORCE-CK804: not 100% native mode: will probe irqs later
NFORCE-CK804: 0000:00:06.0 (rev f2) UDMA133 controller
NFORCE-CK804: neither IDE port enabled (BIOS)
ide-floppy driver 0.99.newide
mice: PS/2 mouse device common for all mice
input: PC Speaker
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP: routing cache hash table of 32768 buckets, 512Kbytes
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
NET: Registered protocol family 1
ACPI: (supports S0 S1 S3 S4 S5)
resid is -1 name is cpu <NULL>
CKRM .. create res clsobj for resouce <cpu>class <taskclass> par=0000000000000000
........init_ckrm_sched_res , resid= 5
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
Starting udev
Creating devices
Loading kernel/drivers/scsi/scsiSCSI subsystem initialized
_mod.ko 
Loading kernel/d3ware Storage Controller device driver for Linux v1.02.00.037.
rivers/scsi/sd_mACPI: PCI interrupt 0000:01:09.0[A] -> GSI 18 (level, low) -> IRQ 18
od.ko
Loading kernel/drivers/scsi/3w-xxxx.ko
scsi0 : Found a 3ware Storage Controller at 0xd800, IRQ: 18, P-chip: 1.3
scsi0 : 3ware Storage Controller
Using anticipatory io scheduler
  Vendor: 3ware     Model: Logical Disk 0    Rev: 1.0 
  Type:   Direct-Access                      ANSI SCSI revision: 00
SCSI device sda: 488395120 512-byte hdwr sectors (250058 MB)
SCSI device sda: drive cache: write back
 sda: sda1 sda2 sda4 < sda5 >
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Loading kernel/dAdaptec aacraid driver (1.1-4 Dec 13 2005 00:17:47)
rivers/scsi/aacraid/aacraid.ko
Loading kernel/d3ware 9000 Storage Controller device driver for Linux v2.26.02.001.
rivers/scsi/3w-9xxx.ko
Loading kernel/fs/jbd/jbd.ko
Loading kedevice-mapper: Allocated new minor_bits array for 1024 devices
rnel/fs/ext3/extdevice-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
3.ko
Loading kernel/drivers/md/dm-mod.ko
Loading kernel/fs/reiserfs/reiserfs.ko
Loading kernel/drivers/md/dm-snapshot.ko
Waiting for /dev/mapper/control to appear: . ok
  Reading all physical volumes.  This may take a while...
  Found volume group "rootvg" using metadata type lvm2
  3 logical volume(s) in volume group "rootvg" now active
ReiserFS: dm-0: found reiserfs format "3.6" with standard journal
ReiserFS: dm-0: using ordered data mode
reiserfs: using flush barriers
ReiserFS: dm-0: journal params: device dm-0, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: dm-0: checking transaction log (dm-0)
reiserfs: disabling flush barriers on dm-0
ReiserFS: dm-0: Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Trying to move old root to /initrd ... /initrd does not exist. Ignored.
Unmounting old root
Trying to free ramdisk memory ... okay
Freeing unused kernel memory: 204k freed
INIT: version 2.85 booting
System Boot Control: Running /etc/init.d/boot
Mounting /proc filesystem                                             done
Mounting sysfs on /sys                                                done
Mounting /dev/pts                                                     done
Boot logging started on /dev/ttyS0(/dev/console) at Tue Feb 21 14:18:29 2006
Mounting shared memory FS on /dev/shm                                 done
Activating swap-devices in /etc/fstab...
Unable to find swap-space signature                                   failed
Checking root file system...
fsck 1.38 (30-Jun-2005)
[/sbin/fsck.reiserfs (1) -- /dev/shm/root] fsck.reiserfs -a /dev/shm/root 
Reiserfs super block in block 16 on 0xfd00 of format 3.6 with standard journal
Blocks (total/free): 524288/393358 by 4096 bytes
Filesystem is clean
Filesystem seems mounted read-only. Skipping journal replay.
Checking internal tree..finished                                      done
Hotplug is already active  (disable with  NOHOTPLUG=1 at the boot promdone
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
Activating device mapper...
Creating /dev/mapper/control character device with major:10 minor:63.
                                                                      done
Scanning for LVM volume groups...
  Reading all physical volumes.  This may take a while...
  Found volume group "rootvg" using metadata type lvm2
Activating LVM volume groups...
  3 logical volume(s) in volume group "rootvg" now active
                                                                      done
Checking file systems...
fsck 1.38 (30-Jun-2005)
Checking all file systems.
[/sbin/fsck.reiserfs (1) -- /var] fsck.reiserfs -a /dev/rootvg/varlv 
Reiserfs super block in block 16 on 0xfd01 of format 3.6 with standard journal
Blocks (total/free): 524288/508836 by 4096 bytes
Filesystem is NOT clean
Replaying journal..
Reiserfs journal '/dev/rootvg/varlv' in blocks [18..8211]: 0 transactions replayed
Checking internal tree..finished
[/sbin/fsck.ext3 (1) -- /boot] fsck.ext3 -a /dev/sda1 
/dev/sda1: clean, 41/49152 files, 22170/196592 blocks                 done
Setting up                                                            done
ReiserFS: dm-1: found reiserfs format "3.6" with standard journal
ReiserFS: dm-1: using ordered data mode
reiserfs: using flush barriers
ReiserFS: dm-1: journal params: device dm-1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: dm-1: checking transaction log (dm-1)
reiserfs: disabling flush barriers on dm-1
Mounting local fReiserFS: dm-1: Using r5 hash to sort names
ile systems...
proc on /proc type proc (rw)
sysfs on /sys tykjournald starting.  Commit interval 5 seconds
pe sysfs (rw)
EXT3 FS on sda1, internal journal
tmpfs on /dev/shEXT3-fs: mounted filesystem with ordered data mode.
m type tmpfs (rw)
devpts on /dev/pts type devpts (rw,mode=0620,gid=5)
/dev/mapper/rootvg-varlv on /var type reiserfs (rw,acl,user_xattr)
/dev/sda1 on /boot type ext3 (rw,acl,user_xattr)                      done
Loading required kernel modules                                       done
Unable to find swap-space signature
Activating remaining swap-devices in /etc/fstab...                    failed
Restore device permissions                                            done
Setting up the CMOS clock                                             done
Setting up timezone data                                              done
Setting scheduling timeslices                                         unused
Setting current sysctl status from /etc/sysctl.conf
net.ipv4.icmp_echo_ignore_broadcasts = 1
net.ipv4.conf.all.rp_filter = 1
                                                                      done
Setting up hostname 'rootserver'                                      done
Setting up loopback interface     lo       
    lo        IP address: 127.0.0.1/8   
                                                                      done
Enabling syn flood protection                                         done
Disabling IP forwarding                                               done
                                                                      done
Creating /var/log/boot.msg                                            done
System Boot Control: The system has been                              set up
Skipped features:                                                                boot.sched
System Boot Control: Running /etc/init.d/boot.local                   done
INIT: Entering runlevel: 3
Boot logging started on /dev/ttyS0(/dev/console) at Tue Feb 21 14:18:35 2006
Master Resource Control: previous runlevel: N, switching to runlevel: 3
Initializing random number generator                                  done
Starting irqbalance                                                   done
coldplug scanning input: *                                            done
         scanning pci: W****.*********W**                             done
         scanning usb: usbcore: registered new driver usbfs
usbcore: registered new driver hub
                                                                      done
         .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .done .  .
Setting up network interfaces:
    lo       
    lo        IP address: 127.0.0.1/8                                 done
Waiting for mandatory devices:  eth-id-00:e0:81:59:52:7b __NSC__
20 19 JBD: barrier-based sync failed on sda1 - disabling barriers
18 17 16 ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 22 (level, low) -> IRQ 17
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: irq 17, pci mem ffffff0000051000
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
usb usb1: Product: OHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.5-7.244-smp ohci_hcd
usb usb1: SerialNumber: 0000:00:02.0
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
15 ACPI: PCI interrupt 0000:00:02.1[B] -> GSI 21 (level, low) -> IRQ 18
ehci_hcd 0000:00:02.1: EHCI Host Controller
13 ehci_hcd 0000:00:02.1: BIOS handoff failed (160, 1010001)
 Devices connected to this controller will not work correctly.
 Complain to your BIOS vendor.
ehci_hcd 0000:00:02.1: irq 18, pci mem ffffff0000053000
ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2
PCI: cache line size of 64 is not supported by device 0000:00:02.1
ehci_hcd 0000:00:02.1: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29
usb usb2: Product: EHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.5-7.244-smp ehci_hcd
usb usb2: SerialNumber: 0000:00:02.1
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 8 ports detected
tg3.c:v3.37 (August 25, 2005)
ACPI: PCI interrupt 0000:04:00.0[A] -> GSI 19 (level, low) -> IRQ 19
eth0: Tigon3 [partno(BCM95721) rev 4101 PHY(5750)] (PCIX:100MHz:32-bit) 10/100/1000BaseT Ethernet 00:e0:81:59:52:7b
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[1] 
eth0: dma_rwctrl[76180000]
NET: Registered protocol family 17
st: Version 20040318, fixed bufsize 32768, s/g segs 256
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0,  type 0
12 11 tg3: eth0: Link is up at 100 Mbps, half duplex.
tg3: eth0: Flow control is off for TX and off for RX.
10 9 
    eth0      device: Broadcom Corporation NetXtreme BCM5721 Gigabit Ethernet PCI Express (rev 11)
    eth0      configuration: eth-id-00:e0:81:59:52:7b
    eth0      IP address: 192.168.4.12/32 (DHCP)                      done
Setting up service network  .  .  .  .  .  .  .  .  .  .  .  .  .  .  done
Starting syslog services                                              done
Starting 3ware DiskSwitch daemon:                                     done
Starting resource manager                                             done
Starting mail service (Postfix)NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
                                                                      done
Starting SSH daemon                                                   done
loading ACPI modules (ac battery ACPI: Power Button (FF) [PWRF]
button ACPI: Fan [FAN] (on)
fan ACPI: Processor [CPU0] (supports C1)
ACPI: Processor [CPU1] (supports C1)
processor ACPI: Thermal Zone [THRM] (51 C)
thermal ) powernow-k8: Found 2 AMD Athlon 64 / Opteron processors (version 1.50.3sles9)
powernow-k8: MP systems not supported by PSB BIOS structure
powernow-k8: init not cpu 0
Starting powersaved                                                   done
Loading keymap qwertz/de-latin1-nodeadkeys.map.gz                     done
Loading compose table latin1.add                                      done
Start Unicode mode                                                    done
Loading console font lat9w-16.psfu  -m trivial (K                     done
Starting hardware scan on bootStarting CRON daemon                    done
BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
                                                                      done
Master Resource Control: runlevel 3 has been                          reached


Welcome to SUSE LINUX Enterprise Server 9 (x86_64) - Kernel 2.6.5-7.244-smp (ttyS0).


rootserver login: